Horsepower CalculatorFrom torque and RPM, quarter-mile time or trap speed

Choose a method: convert torque and RPM straight into horsepower, or estimate your car’s power from a quarter-mile run using the elapsed time or trap speed and the weight of the car with driver.

Free, no sign-up3 calculation methodsHP, kW & PSBy ReviewsWhiz Editorial Team

Your numbers

lb-ft
rpm
lb
sec
mph

How to use the Horsepower Calculator

  1. Pick a method. Use Torque & RPM if you have dyno or spec-sheet numbers. Use Quarter-mile ET or Trap speed if you have a time slip from the drag strip.
  2. Enter your figures. For the drag strip methods, use the weight of the car including the driver and fuel.
  3. Choose the drivetrain loss to convert between wheel and crank horsepower.
  4. Read the results in horsepower, kilowatts and metric PS.
Quick answer: horsepower = torque (lb-ft) × RPM ÷ 5,252. An engine making 300 lb-ft at 5,500 rpm produces about 314 hp at that speed.

Horsepower vs torque

Torque is the twisting force an engine produces. Horsepower is how quickly that force does work, so it combines torque with engine speed. That is why the same torque figure gives more horsepower at higher RPM.

A practical way to think about it: torque is what you feel pushing you into the seat when you press the throttle at low speed; horsepower is what decides how fast the car keeps accelerating at high speed and what top speed it can reach. Diesel trucks make lots of torque at low RPM for towing, while sports cars rev high to make big horsepower.

Because of the way the units are defined, the torque and horsepower curves on a dyno chart always cross at 5,252 rpm when torque is measured in lb-ft.

Estimating horsepower from a quarter-mile run

Drag strip results are a good real-world check of power. The two classic formulas are:

  • Elapsed time (ET) method: HP = Weight ÷ (ET ÷ 5.825)³. ET depends heavily on the launch, traction and shifting, so it often underestimates power for cars that struggle to put power down.
  • Trap speed method: HP = Weight × (Trap speed ÷ 234)³. Trap speed is less affected by the launch, so it is usually the more reliable of the two.

Both formulas estimate the power that reaches the wheels. To compare with a manufacturer’s figure, which is measured at the crankshaft, the calculator adds back the drivetrain loss you choose.

Wheel horsepower vs crank horsepower

Automakers quote crank (brake) horsepower, measured at the engine’s output shaft. A chassis dyno measures wheel horsepower, after power has passed through the transmission, driveshafts, differential and tires. Some is lost along the way as friction and heat.

DrivetrainTypical loss
Manual, rear-wheel drive10% to 15%
Front-wheel drive10% to 15%
Automatic, rear-wheel drive13% to 18%
All-wheel drive15% to 25%

These percentages are rules of thumb. Different dynos also read differently, so compare numbers from the same dyno when testing modifications.

HP, kW and PS

In the US, power is quoted in mechanical horsepower (hp). Europe and much of the world use kilowatts (kW), and many manufacturers also list PS (metric horsepower, from the German Pferdestärke). One hp equals 0.7457 kW, and one hp is about 1.014 PS, so a 300 hp engine is about 224 kW or 304 PS.

The formula behind it

Horsepower = Torque (lb-ft) × RPM ÷ 5,252
HP from ET = Weight (lb) ÷ (ET ÷ 5.825)³
HP from trap speed = Weight (lb) × (MPH ÷ 234)³
Crank HP = Wheel HP ÷ (1 − Drivetrain loss)
kW = HP × 0.7457 · PS = HP × 1.0139

The drag strip formulas assume a well-driven run at sea level in normal conditions. Altitude, heat, poor traction and gearing all change results, so treat them as estimates.

Horsepower facts

5,252 rpm
Where horsepower and lb-ft torque are always equal.
0.7457 kW
The power of one mechanical horsepower.
10 to 25%
Typical power lost between the crank and the wheels.
Trap speed
Usually a better guide to power than quarter-mile time.
1.014 PS
One US horsepower in metric horsepower.
Crank vs wheel
Automakers quote crank power; chassis dynos measure wheel power.

Frequently asked questions

How do you calculate horsepower from torque?
Multiply torque in lb-ft by engine speed in rpm and divide by 5,252. For example, 400 lb-ft at 4,000 rpm is 400 × 4,000 ÷ 5,252 = 305 hp.
Why do torque and horsepower cross at 5,252 rpm?
Because the horsepower formula divides torque × RPM by 5,252. At exactly 5,252 rpm, the two numbers are equal when torque is in lb-ft.
How accurate is the quarter-mile horsepower formula?
It is a reasonable estimate for a well-driven run. The trap speed method is usually within about 5% to 10% of dyno results; the ET method is less reliable because launches vary.
What is the difference between whp and hp?
Whp (wheel horsepower) is measured at the wheels on a chassis dyno. Hp, as advertised, is measured at the crankshaft. Wheel power is lower because of drivetrain losses.
How many kW is 300 hp?
300 hp × 0.7457 = about 224 kW.
Is more torque or more horsepower better?
It depends on use. High torque at low RPM suits towing and everyday driving; high horsepower suits fast acceleration at speed and track driving.

Related tools and guides

Learn how your car works

Plain-English guides to engines, drivetrains and modern car features.

Read the guides →

Results are estimates for general information only. Real output depends on the engine, fuel, weather, altitude and how the measurement was made.